Engine

2Lb . SLIDE HAMMER AND PULLER SETES.HT-1020-2

• A versatile tool that can be used in many ways. The 2 lb slide hammer and an array of attachments can be utilized to aid in pulling seals, bearings, pressed studs, or even for straightening body panels.
• Slide hammer and accessories can be used in many applications.
• Capable of inside spreads from 3/8″ to 1 ¼“ and outer spreads up to 3″.
• Puller reaches depths up to 2 ½”.
• All components are in a blow-molded case for easy storage and organization.

Ford Cam Tools Master Service SetES.HT-1054-2

• The Ball Joint Master Service Kit offers complete coverage of Car and Truck/Van/SUV applications. With 70+ adapters, c-frame and application guide means there is nothing else to add for servicing ball joints.

puller spinning toolES.HT-1055-2

• Ideal for holding camshaft, crankshaft, power steering and accessory pulleys for service.
• 12 in. long handle for extra leverage.
•  Heat treated alloy steel.
• Adjustable jaw opening from 1/4 to 7/8 in.

Crankshaft Pulley HolderES.HT-1056-2

• Prevents engine from turning when removing or installing the crankshaft bolt.
• Hex shape fits hole in center of crankshaft pulley.
• Hole in center allows use of a socket to loosen or tighten the pulley bolt.
• Heavy duty alloy steel construction.
• 50 mm diameter.
• Use 1/2 in. drive breaker bar or ratchet.

18pc A/C Deluxe Automotive Compressor Clutch Hub Remover Installer Puller ToolES.HT-1057-2

• Remover Puller Installer Puller Tool for Auto Car Truck Van SUV.
• Compressor clutch removal tool for GM-Harrison DA-6, HR-5, V-5, A-6 and early R4, Nippondenso Ford/Chrysler A590, C171, FS-6, 6P148A (new style).
• Compressor clutch removal tool for Sanden and Sankyo; York/Tecumseh HR980; Zexel/Mitsubishi CH series, DKS, and Zexel compressors.
• The kit also contains all the necessary tools to reinstall a clutch hub back onto the compressor.

A/c Compressor Clutch Installer/Remover KitES.HT-1058-2

• Replaces clutches found on FS6, C171, 6P & 148 compressors GM R4 & A6, HR-6, DA-6 & V5 A/C compressors, Sanden compressors SD505, 507, 510, 575, 708 & 709.
• 2 & 3 hole puller plate fits most clutches, mechanical force does the pulling.
• Blow molded case for easy storage and transport.

Camshaft Pulley HolderES.HT-1059-2

• Work on Toyota, Nissan, Mazda, OHC enging and other makes.
• Desined to hold camshaft gears stationary, injection pump, other gears and pulleys for both loosening and tightening cam pulley bolts.
• Great holding tool for timing belt changes, cam seal replacement, cam gear removal, camshaft pulleys installation etc.

8PC, Engine Serpentine Belt Adjust Tightener Wrench Tool KitES.HT-1060-2

• Remove & install belts on serpentine systems using spring loaded idler pulleys.
• 1/2" Drive Adapter Included.
• Handle Has a 3/8" Square Drive for Extra Leverage.
• Fits idler pulleys requiring 15mm, 16mm, 18mm hex or 3/8 or 1/2-Inch square drive.
• Also included 13mm, 14mm and 15mm crowfoot wrenches.

16PC, Wrench Serpentine Belt Tension Tool KitES.HT-1061-2

• Designed to assist with the removal and installation of serpentine belts.
• Use on Ford, GM, Chrysler, SAAB, VW, Volvo and other models with Serpentine tensioners.
• Combination of special sockets and crows feet provides complete vehicle coverage.
• Designed for engine compartments with limited access.

9PC Serpentine Belt Tensioner Pulley Alignment Wrench Tool KitES.HT-1062-2

• Professional tool for everyday commercial or occasional DIY use.
• Releases tension on serpentine belts with spring loaded idler pulley.
• This set makes changing serpentine accessory belts easy even in tight spaces.
• Fits idler pulleys requiring 15mm, 16mm or 18mm hex and 3/8" or 1/2" square drives.
• SET Includes:
  1.Long bar total length 490mm, width 19mm (3/8" drive with rubberised handle)
  2.Short bar 230mm, width 25mm (1/2" drive)
  3.13mm / 14mm and 15mm crowfoot wrench
  4.15mm / 16mm and 18mm hex sockets (6 sided)

Car Engine Timing Belt Tension Adjuster Pulley Wrench ToolES.HT-1063-2

• > Special angle designed to adjust the belt tension
  on the free roller.
  > Applicable:VW.AUDI.

BENZ Compressor Belt Pulley WrenchES.HT-1064-2

• > Speciality tool for using on removing/installing
  compressor belt.
  > Pully,special three point design for suitable
  using on parts of the vehicles.
  > Applicable:BENZM112,M113,M272,M273.

5PCS Metric Poly V Belt Spanner SetES.HT-1065-2

• >To operate the Automatic tensioning device of the belt pulley
• > Size: 13,15,16,17,19mm , length 460mm
• > Through the Narrow & long design ,it is possible to use in confined spaces
• >Suitable for all european cars

Fan Clutch Wrench SetES.HT-1066-2

• Used to easily remove or install the fan clutchassembly when replacing water pumps.
• Heavy duty 1/4 in. steel construction.
• Includes 2-1/4 in. fan pulley holding wrench and 1-7/16 in. fan clutch nut wrench for loosening clutch nut assembly.
• Heat treated alloy steel.
• Use 1/2 in. drive breaker bar or ratchet for more torque.

Crank & Camshaft Seal Tool KitES.HT-1069-2

• The kit includes handled adjustable seal puller plus adapters and threaded puller to easily remove and install crank and camshaft seals from 21 - 64mm.
• Long and short pulling arm sets made from S2 tool steel for twice the bend resistance of comparable sets while maintaining slim profile for access.
• Uses OEM crank or cam bolt paired with included stackable sleeves, bushing and mandrel to press in new seals.

10PCS Fan Clutch Wrench SetES.HT-1070-2

• Allows you to hold the fan clutch with the clutch holder tool, while using the special wrench to turn the fan clutch nut.
• Square drive allows attachment of a breaker bar for extra torque.
• A must for any front engine service.
• Works on wide range of Ford, General Motors and Chrysler vehicles.

Flywheel TurnerES.HT-1071-2

• Use this special wrench to turn the flywheel and rotate the engine.
• Folds for easy storage.
• Also holds the flywheel or flex plate when torquing the flywheel or harmonic balancer bolts.

>Self locking ratchet pawl prevents premature release and allows positive locking action. >With 5 size:

A.2"Height capacity:1-1/2"to3-1/8"(40-80mm)ES.HT1072-2 

B.3"Height,capacity:2-1/8"to5"(53- 125m)ES.HT1073-2
C.3"Height,capacity:2-1/8"to7"(53- 175mm)ES.HT1074-2
D.3-1/2"Height,capacity:2-1/8"to5"(54-127mm).ES.HT1075-2

• Use to install pistons in most passenger car and truck engines.
• Self locking ratchet pawl prevents premature release and allows positive locking action.
• With 7 size:
  1. 2" Height, Capacity: 1-1/2" to 3-1/8" (40 - 80mm).
  2. 3" Height, Capacity: 2-1/8" to 5" (53 -125mm).
  3. 3" Height, Capacity: 2-1/8" to 7" (53 - 175mm).
  4. 3-1/2" Height, Capacity: 2-1/8" to 5" (53 - 125mm).
  5. 3-1/2" Height, Capacity: 3-1/2" to 7"(89 - 178mm).
  6. 4" Height, Capacity: 2-3/8" to 7" (60 - 175mm).
  7. 6" Height, Capacity: 2-3/8" to 7" (60 - 175mm).

E.3-1/2"Height,capacity3-1/2"to7"(89-178mm).ES.HT-1076-2
F.4"Height,capacity:2-3/8"to7"(60- 175mm)ES.HT-1077-2
G.6"Height,capacity:2-3/8"to7"(60-175mm)ES.HT-1078-2

Lever Valve spring CompressorES.HT-1079-2

• Compresses Valve Springs on GM V-8 Engines with Stud-Type Rocker Arms without having to remove cylinder heads.
• Compresses valve springs without removing head.
• Allows access for service to most valve train components.
• For GM 8 cylinder engines and others with stud type rocker arms.

Piston ring installerES.HT1080-2

• Made of all steel with tapered jaws for quick and easy installation.
• Adjustable piston mounting piston piston ring spreader - expansion pliers tool for mounting. 3/64" to 1/4" inches for safe and fast piston ring mounting with simple ring expansion.
• The most common piston and piston ring diameters range from 3/64" to 1/4" (1.2mm to 6.4mm).
• With tapered jaws and vinyl coated handle with non-slip rubber handle, it provides safe and comfortable operation and reduces user fatigue.

GM Water Pump Remover And Installer SocketES.HT1081-2

• Specially designed for use on 1993 to current Northstar 4.6 Liter, 1997 to current Aurora 4.0 Liter.
• 1/2"Ｄr fit for break bar or ratchet wrench, unique design efficiently removes and install water pump.
• This tool is self centre in the water pump housing fully engaged the water pump for removal and installation.
• Size: 86MM O.D X 80MM I.D X 59MM length, Drop forged heavy duty constructure.

Air Condition Line Disconnect TOOLES.HT1082-2

• Quickly, easily and safely separate fuel lines, transmission lines and oil lines.
• Anodized aluminum finish resists corrosion.
• Suitable for most Ford Vehicles.

FUEL FILTER/LINETOOLES.HT1083-2

• Safely separates fuel lines, transmission lines, and oil lines.
• Designed for use with OEM Ford fittings.
• Color-coded for quick reference.
• Includes 1/4 in., 5/16 in., and 3/8 in. tools.
• Cast and machined aluminum with anodized finish.

Clutch Coupling ToolES.HT1084-2

• Reaches and disconnects the hydraulic clutch line from the clutch slave cylinder without damage to the coupling or clutch line.
• Fits Ford Hydraulic clutches:1988 and later model Ford F series trucks, Bronco ll's, Rangers and Explorers; 1989 and later model Thunderbirds; Mercury Cougars.

GM Clutch Line Disconnect ToolES.HT1085-2

• This is a versatile tool for disconnecting clutch lines when you're working on clutch assemblies or slave and master cylinders.
• The bent end works on 1996 to 2004 full-size 2WD and 4WD trucks Chevrolet S-10 Blazer and pickups.
• The straight end is for 1993 to 1994 Chevrolet Lumina sedan 1995 to 2000 Chevrolet Monte Carlo 1993 to 1999 Buick Regal 1998 to 2002 Olds Intrigue 1993 to 1997 Olds Cutlass Supreme and Pontiac Grand Prix.

9PC SPRING LOCK COUPLING TOOLES.HT1086-2

• Includes spring locking tool:3/8" RED,1/2" BLUE,5/8" BLACK,3/4" WHITE.
• Fuel disconnect tool:3/8" YELLOW,1/2" GREEN.
• Fuel line fitting disconnect tool:5/16" GREY,3/8" CYAN FORD/GM quick disconnect
• Tool:1/2" BLACK

A/C and Fuel Line Quick Disconnect SetES.HT1087-2

• The engagement lip should be approximately
  the same diameter as the spring or open side
  of fuel line fitting.
• Twist tool to open and slip over fuel line fitting.
• A "click" may be heard as fuel line fitting release.
• Separate fuel line pieces.
• Size:15/16",3/8",1/2",5/8",3/4",7/8".

Fuel Line Disconnect ToolES.HT1088-2

• Use to release spring lock couplings on fuel and
  air conditioning lines on most Ford and Chrysler
  LH series vehicles.
• 4 size: A (7/8"), B (3/4"), C (5/8"), D (1/2").

Fuel Line Disconnect ToolES.HT1089-2

• Use to release the fuel line locking mechanism on 1989 and newer GM, 1990 and newer Ford and some 1990 and newer Mazda vehicles.Also fits Chrysler fuel-injected vehicles (except imports).
• Fits 5/16" and 3/8" fuel lines.

8pcs.fuel&transmission Lin Disconnect Tool SetES.HT1090-2

• Anodized aluminum.
• Separate fittings on fuel lines, fuel filters & fuel tank return lines.
• Sizes: 1/4", 5/16", 3/8" & 1/2" Oil Cooler Line Disconnect Tool.
• Separates automatic transmission oil cooler lines on Ford Taurus and Escort with AXOD and ATX transmissions.
• Fuel line disconnect tool allows damage free fuel line quick connect coupler release.
• Fits any 5/16" or 3/8" fuel line found on GM, Ford or Chrysler cars.
• Ford fuel line coupling tool provides easy, damage-free fuel line separation.
• Works on 1990 and newer Ford Ranger and Explorers with 4.0L, 6 cylinder engines.
• Disconnect tool allows quick separation of quick connectors found on radiators, transmissions and power steering lines.
• Releases the fingers on transmission-to-radiator oil cooler line easily without damage to the hose or connector.
• Works on 1986 and newer Ford Tauruses and Mercury Sables with an AXOD, AOD or ATX transmission.
• Quick disconnect coupler tool slides down the line and into the connector separating the clip apart without damaging the quick connect seals allowing removal of clip.
• Works on late model Ford and GM vehicles.

15PC MASTER DISCONNECT KITES.HT-1091-2

Fuel & Transmission Line Disconnect Set:

• Anodized aluminum.

• Separate fittings on fuel lines, fuel filters & fuel tank return lines.

• Sizes: 1/4"", 5/16"", 3/8"" & 1/2"" Oil Cooler Line Disconnect Tool.

• Separates automatic transmission oil cooler lines on Ford Taurus and Escort with AXOD and ATX transmissions.

• Fuel line disconnect tool allows damage free fuel line quick connect coupler release.

• Fits any 5/16"" or 3/8"" fuel line found on GM, Ford or Chrysler cars.

• Ford fuel line coupling tool provides easy, damage-free fuel line separation.

• Works on 1990 and newer Ford Ranger and Explorers with 4.0L, 6 cylinder engines.

• Disconnect tool allows quick separation of quick connectors found on radiators, transmissions and power steering lines.

• Releases the fingers on transmission-to-radiator oil cooler line easily without damage to the hose or connector.

• Works on 1986 and newer Ford Taurus and Mercury Sable with an AXOD, AOD or ATX transmission.

• Quick disconnect coupler tool slides down the line and into the connector; separating the clip apart without damaging the quick connect seals allowing removal of clip.

• Works on late model Ford and GM vehicles.

  Oil Cooler Line Remover:

• Anodized aluminum.

• This unit is used to disconnect transmission oil cooler lines.

• Works on 2003 and 2004 Ford Explorer (V8), 2004 Ford F150, and 2004 Cadillac CS.

• Unique design to clear the flare and disconnect the new style clips.

  Air Conditioning & Fuel Line Disconnect Tool Set:

• Sizes 5/16", 3/8", 1/2", 5/8", 3/4" and 7/8" Air Conditioning & Fuel Line Disconnect Tool:

• Allows easy disconnection of air conditioning lines & quick connect fuel lines.

• Six distinctive tools allow the disconnecting of spring lock couplings air conditioning lines found on Ford and Chrysler.

• Allows usage on fuel line quick connect couplings found on GM, Ford, and Chrysler.

• 5/16" Disconnect Tool allows usage on push lock connectors found on Ford radiators and transmission lines.

full cobverage disconnect tool setES.HT1092-2

• works on quick connect fuel lines on ford on ford,GM.and chrysler,and on the spring lock fuel line couplings on ford's popolar PFI system >work on 5-16",3/8"and 1/2"fuel lines vehicle manufacturer >case dimension:L23"*W10"*H2-1/2" net weight:6-1/3lbs (2.98kgs)

TRIM CLIP PLIERSES.HT-1102-2

• Removes and saves all types of clips.
• Great for removing door panels.
• The front of the tools is tarred will fit easily under a clip,
  spread the jaws lightly so they will go under and around
  the clip then,close the jaws and the clip saver removes
  the clip without damage to the clip.

RELAY PLIERSES.HT-1103-2

• > Pliers for removing electrical relays on most
  domestic and import vehicles.
  > Offset handle and thin tips allow access to relays in
  confined areas.
  > Specially designed tips are angled to fit slots or edge
  of relay cover.
  > This allows relay to pop free from socket with less chance
  of damaging relay cover.
  > Also works on many heavy duty and industrial applications.
  > Also removes truck leaf spring bushings.
  > Pneumatic bushing driver set removes and installs
  truck and trailer1-3/8" anchor pin bushings and
  stuck anchor pins.
  > Drice the bushing out with the small cone.
  > Use the larger cone to install bushing to the proper depth.

LOCK RING PLIERSES.HT-1104-2

• >Removes lock rings on brakes,clutch shafts,transmissions,master cylinders,etc.
  >Spring loaded jaws.
  >Vinyl grip handles.
  >Knurled outer tips hold rings securely.

Flexible hose clampES.HT-1105-2

• Allows for removal of plastic and/or metal self-tightening hose clamps with diameters of 11/16" - 2-1/2" (18mm - 54mm).
• Precision clamp on end of flexible cable allows for extended reach where other models cannot reach.
• Pliers can be locked, freeing up your hands and making your job easier and faster.

Pneumatic Brake Caliper Rewind Tool / 4 pcsES.BS-1112-2

• universal set for turning and pressing brake pistons on almost all car models
• for air pressure assisted resetting of brake pistons
• hand lever for rotary function, suitable for left and right turns
• Brake Rewind Adaptor with Adjustable two-pin Drive.
• The set also includes an adjustable three-pin adaptor which is de • The set also includes an adjustable three-pin adaptor which is designed for electronic park brake calipers. Use in conjunction with Electronic Park Brake (EPB) reset equipment.
• A standard two-pin adaptor is also included which enables it to be used with any piston adaptor, for example, single-pin versions.
• also suitable for brake callipers with hand brake function
• suitable for following car models: Alfa Romeo,Audi,Citroen,Fiat,Ford,GM Honda,Jaguar,Lancia,Land Rover, Mazda,Nissan, Peugeot,Renault, Rover, Saab, Seat, Subaru, Toyota, Volvo, VW
• working pressure: 5 to max. 8 bar

Valve Spring Compressor KitES.BC-1119-2

• For overhead CAM engines.
• Capacity: 75-140mm. Throat clearance: 150mm.
• Universal model with fixed jaws, CAM action provides a parallel lift.
• Automatic locking leaves hands free to continue jobs.
• Intended for use on OHC engines and a wide range of OHV and CVH engines.

Valve Spring Compressor KitES.BC-1120-2

• Suitable for use on mulit-valve pertrol & diesel engines with deep seaed valves.
• Also for use with OHC OHV&CVH engines.
• Capacity: 55mm-175mm. Throat clearance: 165mm.

Valve Spring Compressor KitES.BC-1121-2

• For small/medium OHV engines.
• Capacity: 75-165mm. Throat clearance: 150mm.
• Universal model with strong adjustable cam-action, Parallel lift and automatic locking.
• Suitable for many popular small and medium OHV engines.

Brake Piston Reset Tool
with Ratchet FunctionES.BC-1123-2

• for damage-free resetting of brake pistons
• allows centered, tilt-free resetting
• no damage to seals, pistons and cylinders
• required for maintenance and brake pad replacement
• suitable for almost all vehicle types with floating and fixed callipers without integrated handbrake function
• spindle ratchet mechanism (reversible) reduces the effort
• solid construction with hardened resetting plates
• dip coated handle
• working range from 40 - 68 mm
• length: 270 mm

Brake Piston Reset Tool
with Ratchet FunctionES.BC-1124-2

• For damage-free resetting of brake pistons
• Allows centered, tilt-free resetting
• No damage to seals, pistons and cylinders
• Required for maintenance and brake pad replacement
• Suitable for almost all vehicle types with floating and fixed callipers without integrated handbrake function
• Spindle ratchet mechanism (reversible) reduces the effort
• Solid construction with hardened resetting plates
• Dip coated handle
• Working range from 40 - 68 mm

Brake Piston Reset Tool /with double guide /universal TypeES.BC-1125-2

• for pushing back the brake pistons on e.g. front brake callipers
• suitable for most cars and vans
• two guides for very stiff pistons
• made of cast steel with carbon steel spindle

Master Disc Brake Kit /48 pcsES.BC-1126-2

• for rewinding the brake piston e.g. when replacing the brake pads
• wind-back spindle (clockwise)
• wind-back spindle (counterclockwise)
• empty holder for spindle grease, for smooth working with the brake piston reset spindles
• pin punches, Ø 5.4 mm
• pin punches, Ø 6 mm, with 3 mm pin
• 6 mm L-type hexagon wrench
• 8 mm L-type hexagon wrench
• impact socket, 6-point, 12.5 mm (1/2"), 19 mm
• impact socket, 6-point, 12.5 mm (1/2"), 14 mm
• bit socket, 12.5 mm (1/2"), 10 mm
• T-Star bit socket (for Torx), 10 mm (3/8"), T45
• 4 counterholding plates
• 35 wind-back adaptors, suitable for most models like BMW, VW, Skoda,Seat, Ford, Honda, Alfa Romeo, Suzuki, Nissan, Toyota, etc

Adjustable EPB Brake Adaptor 3 Pin - 2 Pin Drive / 2 pcsES.BC-1127-2

• universal set for turning and pressing brake pistons on almost all car models
• Brake Rewind Adaptor with Adjustable two-pin Drive.
• The set includes an adjustable three-pin adaptor which is designed for electronic park brake calipers. Use in conjunction with Electronic Park Brake (EPB) reset equipment.
• two-pin quickly and easily adjust from 15mm to 35mm distance between pin centres, requires 3mm hex key to lock pins. Pin diameter: 4mm, protruding 2.14mm from face of tool.
• Pins designed to shear at 50Nm
• Applications(3-pin): BMW: E89, F10, F11, F12, F13, F18, F25, Mini; VAG: A4, S4, A5, S5, A6, S6, A8, S8, Passat 3C, Passat CC, Tiguan;Renault: Grande Scenic; Volvo: S60, S80, V60, V70, XC60, XC70.

Adjustable EPB Brake Adaptor
3 Pin - 2 Pin 3/8"D / 2 pcsES.BC-1128-2

• universal set for turning and pressing brake pistons on almost all car models
• Brake Rewind Adaptor with Adjustable two-pin Drive.
• The set includes an adjustable three-pin adaptor which is designed for electronic park brake calipers. Use in conjunction with Electronic Park Brake (EPB) reset equipment.
• two-pin quickly and easily adjust from 15mm to 35mm distance between pin centres, requires 3mm hex key to lock pins. Pin diameter: 4mm, protruding 2.14mm from face of tool.
• Pins designed to shear at 50Nm
• Applications(3-pin): BMW: E89, F10, F11, F12, F13, F18, F25, Mini; VAG: A4, S4, A5, S5, A6, S6, A8, S8, Passat 3C, Passat CC, Tiguan;Renault: Grande Scenic; Volvo: S60, S80, V60, V70, XC60, XC70

Brake Piston Wind-Back Tool / 5 pcsES.BC-1129-2

• for wind back brake systems for right hand thrust bolts

• 1 x double sided pin adaptor with 32mm & 22mm pin centres

• 1 x pin adaptor with 20mm pin centres

• 1 x adaptor with various size drives 37mm, 42mm and 54mm

• for use with most makes & models

• maximum opening 40mm

Brake Piston Wind-Back Tool / 4 pcsES.BC-1130-2

• for wind back brake systems for right hand thrust bolts

• 1 x double sided pin adaptor with 32mm & 22mm pin centres

• 1 x pin adaptor with 20mm pin centres

• for use with most makes & models

• maximum opening 40mm

Brake Piston Wind-Back Tool /3 pcsES.BC-1131-2

• Designed for rewinding brake piston with right-handed thread

• Fitted for most European and Japanese Cars with right-handed thread

• Expert quality, complete with reaction plate and double sided adapter

• Adapter double sided:-1 side: (22mm centers / 6mm diameter pins (approx.) Alfa Romeo, Audi, Citroen, Fiat, Ford, Honda, Jaguar, Nissan, Peugeot, Renault, Rover, Saab, Seat, Subaru, Volkswagen, Volvo and etc. -2 side: (33mm centers / 6mm diameter pins (approx.)Ford, Mazda, Mitsubishi, Toyota and etc

Brake Piston Reset Tool /universal
left + right Thread / 6 pcsES.BC-1132-2

• for resetting the brake piston when replacing the brake pads
• suitable for most diesel engines
• 1 adjustable 2-pin brake piston adaptor
• 1 adjustable 3-pin brake piston adaptor
• 1 magnetic adaptor plate for mounting standard brake piston adaptors
  with fixed pins
• 1 counterholding plate
• 1 two-way adaptor driver

Master Disc Brake Kit /48 pcsES.BC-1133-2

• Adjusts front and rear brake calipers on most domestic and import vehicles
• Set includes brake bleeder wrenches: 1/4" x 3/8", 8mm x 10mm, 3/8" x 5/16"; disc brake caliper wrench 3/8", disc brake pad
  spreader, deluxe tubing bender, compact tubing cutter, adapters: 1-1/4", 1-13/32", 1-7/8", 2", 2-5/32", 2-1/2"; short 2-prong
  x 1-21/32" adapter; long 2-prong x 1-21/32" adapter; star sockets: T-40, T-45, T-47, T-50, T-55, T-60; hex bit sockets: 1/4",
  5/16", 3/8", 7mm, 8mm, 10mm; T-handle, disc, and plate

Master Disc Brake Kit /48 pcsES.BC-1134-2

• Adjusts front and rear brake calipers on most domestic and import vehicles
• Set includes brake bleeder wrenches: 1/4" x 3/8", 8mm x 10mm, 3/8" x 5/16"; disc brake caliper wrench 3/8", disc brake pad
  spreader, deluxe tubing bender, compact tubing cutter, adapters: 1-1/4", 1-13/32", 1-7/8", 2", 2-5/32", 2-1/2"; short 2-prong
  x 1-21/32" adapter; long 2-prong x 1-21/32" adapter; star sockets: T-40, T-45, T-47, T-50, T-55, T-60; hex bit sockets: 1/4",
  5/16", 3/8", 7mm, 8mm, 10mm; T-handle, disc, and plate

Universal Oil Filter Wrench / 60 – 80 mmES.BC-1150-2 

• Mechanical locking of the oil filter wrench simplifies subsequent attachment of the reversible ratchet to the oil filter wrench.
• The oil filter tensioner adjuster always remains under tension when the reversible ratchet is moved backwards
• Infinitely adjustable
• Use with wrench size 21 mm or 12.5 mm (1/2 inch) reversible ratchet
• Optimal hold when loosening the oil filter thanks to left-toothed jaws
• For oil filters in areas with restricted access
• Clockwise/anti-clockwise application enables operation of the screw connection
• Drive: Outside hexagon 21 mm, Square, hollow 12.5 mm (1/2 inch)
• Diameter (min-max): 60 - 80

Universal Oil Filter Wrench / 80 – 115 mmES.BC-1151-2

• Mechanical locking of the oil filter wrench simplifies subsequent attachment of the reversible ratchet to the oil filter wrench.
• The oil filter tensioner adjuster always remains under tension when the reversible ratchet is moved backwards
• Infinitely adjustable
• Use with wrench size 22 mm or 12.5 mm (1/2 inch) reversible ratchet
• Optimal hold when loosening the oil filter thanks to left-toothed jaws
• For oil filters in areas with restricted access
• Clockwise/anti-clockwise application enables operation of the screw connection
• Drive: Outside hexagon 22 mm, Square, hollow 12.5 mm (1/2 inch)
• Diameter (min-max): 80 - 115

Universal Oil Filter Wrench / 115 – 140 mmES.BC-1152-2

• Mechanical locking of the oil filter wrench simplifies subsequent attachment of the reversible ratchet to the oil filter wrench.
• The oil filter tensioner adjuster always remains under tension when the reversible ratchet is moved backwards
• Infinitely adjustable
• Use with wrench size 24 mm or 12.5 mm (1/2 inch) reversible ratchet
• Optimal hold when loosening the oil filter thanks to left-toothed jaws
• For oil filters in areas with restricted access
• Clockwise/anti-clockwise application enables operation of the screw connection
• Drive: Outside hexagon 24 mm, Square, hollow 12.5 mm (1/2 inch)
• Diameter (min-max): 115 - 140

Oil Filter Claw Wrench Ø60-120mmES.BC-1153-2

• Satin finished carbon steel construction with 3/8" & 1/2"Sq drive.
• Also suitable for use with a 21mm spanner.
• Claws grip filter tighter as more torque is applied.

Oil Filter Claw Wrench Ø65-130mmES.BC-1154-2

• Satin chrome finish steel construction with 3/8" & 1/2"Sq drive.

• Also suitable for use with a 21mm(13/16") spanner.

• Claws grip filter tighter as more torque is applied to wrench

Oil Filter Wrench Set /30 pcsES.BC-1154-2

Air Conditioning Car Oil Injection ToolES.BC-1159-2

• Dye injector can be used with manifold gauge set or any evacuation or recharging equipment.

• This injector may be used to add most air conditioning additive to our system from oil, dye, stop leak, etc.

• This product is pure liquid refrigerant oil filling tube, fine quality, has a long service life.

• It is no need to unhitch the refrigerant inside the system (the system does not need in vacuum condition).

• Suitable for filling up the automobile air conditioning refrigeration system of R134A (need to get help from a transfertool), R12, R22.

• Refrigeration oil can be filled into the automobile air conditioning.

• High pressure, oil-resistant, practical, wear-resistant, corrosion-resistant, do not harden.

Transmission Filling Adaptor Set/15 pcsES.BC-1166-2

• incl. 15 adapters with different output angles and adapter threads
• suitable for example for Honda, for Nissan, for BMW, for Audi, for VW, for DSG, for Porsche, for Mini Cooper, for Mercedes Benz
• a short adapter for VW and Audi
• a long adapter for VW, Audi and Porsche
• a universal adapter for BMW, for Honda, for Nissan, etc.
• ATF-101: for FORD, 1/8-27 (NPT)
• ATF-102: Universal for BMW, for Honda, for Nissan, etc.
• ATF-103: for VAG, for VW, for Audi, for Skoda
• ATF-104: for VW, for AUDI, for Porsche
• ATF-105: for VW, for AUDI, for MIni Cooper, M10x1.0
• ATF-106: for VW, for AUDI, for DSG, M24x1.25
• ATF-107: for VW, for AUDI, for CVT, M22x1.5
• ATF-108: for Mercedes Benz, M12x1.5
• ATF-109: for VW, for Skoda, M18x1.5
• ATF-110: for VAG, M30x1.5
• ATF-111: Universal Flexible Hose 300 mm (for Honda, for Hyundai, for Kia, etc)
• ATF-112: for VOLVO 5/16-24 (UNF)
• ATF-113: for Toyota, for Lexus, M18 x 1.5

27PC Transmission on Oil Jug joint SetES.BC-1167-2

12PCS Snap ring pliers setES.JY-1175-2

• 1.Heat treated steel construction with blackened finished for strength and resistance to corrosion.
  2.All circlip pliers feature reversible joints enabling use for either external or internal circlips.
  3.Fitted with comfortable vinyl grips.
  4.Supplied in a carry-case.
  Include:
  6"tip pliers,0.038"tips(0°,45°,90°)
  6"tip pliers,0.047"tips(0°,45°,90°)
  8"tip pliers,0.070"tips(0°,45°,90°)
  9"tip pliers,0.090"tips(0°,45°,90°)

4 In 1 Circlip PliersES.JY-1176-2

• 1.To open external snap rings,posotion jaws on upper pins through upper holes and replace pin.
  2.To open internal snap rings,posotion jaws on upper pins through upper holes and replace pin.
  3.Use 45°jaws to reach into tight place to install or remove snap rings.
  4.Use 90°jaws for situations requiring straight-in application of snap ring.
  5.Can be used on 3/8" to 2" internal and external snap rings features interchangeable stralght,45°and 90°heads high carbon steel jaws with black finish

2pc Double End Circlip Pliers SetES.JY-1177-2

• 1.Make removing and installing snap rings fast and easy.
  2.Work on both internal and external style snap rings.
  3.Snap ring fits into grooves,providing a shoulder for holding compoments in place.
  4.Release easily when rings is in posotion

5pcs American type circlip plier set（2pcs 8" and 3pcs 6")ES.JY-1178-2

• 1.Manufactured from high carbon steel with heat-treatment and blackened finish.
  2.Pliers can be reversed for internal and external use.
  3.Selection of straight and angled tip.
  4.PVC dipped handles
  5.Contents:straight 200mm,150mm x2,angle 90°180mm，135mm

Dry Type Transmission Oil-Seal Installer/RemoverES.JY-1179-2

• Specially designed to use on dry type transmission oil-seal installer/remover.
  Applicable:Volvo,Ford Transmission DPS6.
  FM number:307-671/307-672/307-673/307-674

Dry Type Transmission Dual Clutch RestorerES.JY-1180-2

• Designed to release and reset the dual clutch before installing back to the transmission.
  Applicable:VOLVO,FORD,transmission DPS6.
  FM number:307676

T-Handle Ignition Coil Puller Set For VAG ENGINES 4PCSES.JY-1181-2

• Updated set suitable for installation/removal of ignition coils and separating the HT leads from deep-seated spark plugs on VAG vehicles.
  Long shafts with composite T-type handle for added control and stability.
  Prevents damage to ignition coils whilst allowing faster removal.

Adjustable Angle Oil Filter PlierES.JY-1182-2

• 1.Jaws are adjustable angle allowing use of the wrench pliers from multiple points of access.
  2.Slip-joint handle offers a wide size range for use on 2-1/4" to 4-3/4"oil and fuel filters
  3.Indents every 30° for 180° of total adjustment.
  4.Adjustment allows for anywhere from side access

Valve Spring Compressor For Universal use on SOHC and DOHC enginesES.JY-1183-2

• Designed to allow the removal of vavle spring and vavle stem oil seals with the cylinder head in place.
  Fast set up time due to the twin raio pivot system.
  Single handed operation.
  Contents:
  1.support bar X 2
  2.spark plug air-line adaptor
  3.adjustable upright X 2
  4.compressor force screw assembly
  5.Valve adaptor
  6.extension rods

Valve Spring Compressor Keeper Seal on Engine Remove Install ToolES.JY-1184-2

• Permits valve springs and valve stem oil seals to be replaced without the need to remove the cylinder head when used in conjunction with VS1601 Compressed Air Adaptor.
  Reversible jaw adaptor and automatic cam action lock to pre-set spring tension.
  Suitable for use on a wide range of OHV, OHC and CVH engines.
  Note: Not suitable for engines with deep-seated valves.

Overhead Valve Spring CompressorES.JY-1185-2

• Easily removes valve springs without removing cylinder head.
  Offset jaws easily grip and compress valve springs.
  Use with flexible air valve holders and air holder fitting to keep valves in place.

3pc Extended Reach Hose Clamp Pliers SetES.JY-1186-2

• Fully adjustable hose clamp pliers enable the professional technician to access.release rension and remove most constant tension hose clamps ,no matter what their size
  Newly designed superior ENCLOSED RATCHET MECHANISM for safe operation
  Set includes straight ,45°& 90° angled heads for optimum positioning

35°Waffle Grid Hose Clamp PlierES.JY-1187-2

• 32x19mm head w/ multi-directional slotted pattern.
  Spring-loaded w/ locking mechanism.
  65mm range.
  Extra-long (11-3/4" 28cm)for reach.
  Cushion grips

Waffle Grid Hose Clamp PlierES.JY-1188-2

• 32x19mm head w/ multi-directional slotted pattern.
  Spring-loaded w/ locking mechanism.
  65mm range.
  Extra-long (11-3/4" 28cm)for reach.
  Cushion grips

Type Valve Stem Cutting PlierES.JY-1189-2

• Length 230mm
  Maximum opening 30mm x 18mm cutting jaw
  Ideal for use in tyre shops and garages
  For replaceable Tyre valves see our Connect Workshop Consumable range

30PCS Electrical Terminal Release KitES.JY-1190-2

• Special design to release terminals from the plastic connectors without damaging either.
  Release terminals on most body wiring connectors.
  Applicable:suitable for most vehicles

Hose Clamp Pliers（0-38mm / 22-55mm）SetES.JY-1191-2

• Hose Clamp plier 0-38mm x 240mm long.
  Jaw Charom Molybdenum -handle Carbon steel nickel plated finish & electro deposited coating.
  Suitable for a variety of ring type or flat band hose clips /clamp.
  Special waffle shape of jaws securely reaches,grabs,removes or locks hose clamp in place.
  Patented Product.

Glow Plug Connector Pliers(Straight) SetES.JY-1192-2

• Special designed to remove stubborn and hardly accessible glow plug connectors which installed on the latest generation engines.
  Applicable :Benz,BMW,VW,Audi etc

INNER–DRIVESHAFT PRY BARES.JY-1194-2

• Specially designed to engage between the inner driveshaft and the gearbox housing to lever out the driveshaft.
  Total length: 390mm, jaw width: 82mm.
  Applicable: FORD, MAZDA, VOLVO, RENAULT, DACIA and other front wheel drive vehicles.

Banjo , 3/8", 5/16", 1/2" Auto Steel Line Stopper KitES.JY-1195-2

• Use to plug steel lines once disconnected.
  Prevents fluid leaks and contamination during service.
  Use with any automotive fluid.
  Spring loaded design installs in seconds.
  Specifications: Banjo, 3/8”, 5/16”, 1/2”
  Contents:
  Banjo Steel Line Stopper x 1
  3/8” Steel Line Stopper x 1
  5/16” Steel Line Stopper x 1
  1/2” Steel Line Stopper x 1

Metal Line Stopper 11pcsES.JY-1196-2

• To plug the metal line and prevent fluid leakage in disconnection.
  Used in fuel lines ,brake line,power steering and transmission coolerlines.
  Suitable for banjo fittings.
  Rubber insert accessory for quick plug.

Engine Brake Adjustment Tools for Cummins ISX Engine Jake Brake Feeler Gauge（4.1mm ,4.6mm , 7mm）ES.JY-1198-2

• excellent performance, also avoid any unwanted catastrophic failures or engine blows .
  (2)Engine brake adjustment tool 3.4 MM alternative to # 5298757 .
  (3)The 3.4mm area is precision ground to +/- .0005 inch .
  (4) Made of high standard steel anodized black finish,with great strength and PVC coated handle. Design with OEM data, directly replace .
  Using Instruction
  1.Loosen the locknut on the brake lever adjusting screw, and back out the adjusting screw one turn.
  2.Insert the feeler gauge( 3.4 mm shim, between the bottom of the engine brake piston and the top of the exhaust valve pin on the exhaust valve crosshead.
  3.Tighten the adjusting screw until drag on the feeler gauge is felt.
  (Proper drag means that there is no motion of the brake lever camshaft follower against the cam lobe.)
  4.Hold the engine brake lever adjusting screw and tighten the locknut.

3PCS PLASTIC LIGHT DUTY O-RING TOOL SETES.JY-1199-2

• Removing/manipulating O-rings, small seal/gaskets, clips.
  Cleaning air vent assemblies and tight gaps in interior parts.
  Flexible, durable and easy to use in difficult to reach access panels.
  Handling delicate wiring, composite electrical connectors.
  Non-marring material ; Non-scratch.

3PCS PLASTIC LIGHT DUTY SCRAPER TOOL SETES.JY-1200-2

• Multiple uses for delicate surface finishes and close tolerance components.
  Flexible, durable and easy to use.
  Unique tips ensure economical, consistent and aesthetic removal.
  Non-marring material ; Non-scratch.
  Offers control and precision during delicate assembly, repair or restoration work.

12PCS Snap ring pliers setES.JY-1201-2

• 1.Heat treated steel construction with blackened finished for strength and resistance to corrosion.
  2.All circlip pliers feature reversible joints enabling use for either external or internal circlips.
  3.Fitted with comfortable vinyl grips.
  4.Supplied in a carry-case.
  Include:
  6"tip pliers,0.038"tips(0°,45°,90°)
  6"tip pliers,0.047"tips(0°,45°,90°)
  8"tip pliers,0.070"tips(0°,45°,90°)
  9"tip pliers,0.090"tips(0°,45°,90°)

12PCS Snap ring pliers setES.JY-1203-2

• 1.Heat treated steel construction with blackened finished for strength and resistance to corrosion.
  2.All circlip pliers feature reversible joints enabling use for either external or internal circlips.
  3.Fitted with comfortable vinyl grips.
  4.Supplied in a carry-case.
  Include:
  6"tip pliers,0.038"tips(0°,45°,90°)
  6"tip pliers,0.047"tips(0°,45°,90°)
  8"tip pliers,0.070"tips(0°,45°,90°)
  9"tip pliers,0.090"tips(0°,45°,90°)

5pc Oil Filter PlierES.JY-1204-2

• 1.The body of the wrench is precision CNC machined from 6061 T6 aluminum and anodized in gunmetal grey, while the drive hub uses 7075 T6 aluminum and is anodized red.
  2.It can be operated using a 3/8" ratchet or with a 24mm / 15/16" socket or wrench
  3.Include:64.3mm 14flute;86.6mm 16flute;90mm 15flute;84.4mm 14flute;74mm 14flute

Ratchet Extension Drive Bar(HEAVY DUTY)ES.JY-1205-2

• Internal gear is made of CR-MO, max torque: 130Nm, breaking torque: 161Nm.
  Enables easier works in confined spaces, such as water pump, power steering pump and transmission.
  Provided with two square drive adapters in 1/4"Dr and 3/8"Dr.
  Chain-driven mechanism enhances working durability and smoothness.
  Length: 340mm, Head: Ø36mm.

Oil Filter Adjustable Wrench Pliers Hand Removal Plier Tool 60 -120mmES.JY-1206-2

• 30 degree Angled head allows access to previously impossible to reach areas.
  Jaws auto-adjust with one-hand operation.
  Layered steel construction for added strength.
  Non-slip shaped cushioned grips for comfort.
  Capacity: 60-120mm.

18PC Alternator Freewheel Pulley Removal SetES.HS-1293-2

• Material: 6150CRV, A3 steel, plastic, surface sandblasted, black scale
  Suitable for: disassembly and assembly of generator pulleys for models such as Volkswagen, Audi, BMW, Ford, Skoda, Mercedes Benz, Opel, Volvo, Porsche, Renault, etc

24PC Alternator Freewheel Pulley Removal SetES.HS-1294-2

• Material: 6150CRV, A3 steel, plastic, surface sandblasted, black scale
  Suitable for: disassembly and assembly of generator pulleys for models such as Volkswagen, Audi, BMW, Ford, Skoda, Mercedes Benz, Opel, Volvo, Porsche, Renault, etc

6PC Alternator Freewheel Pulley Removal Set S2 BITSES.HS-1295-2

• Suitable for Audi,BMW,Fiat,Ford,
  Mercedes,Renault,Seat,vW and Porsche
• Size:T40,T50,M8,M10,H8,H10 112"
  Drivex1OMM ADAPTER

30PC Alternator Freewheel Pulley Removal SetES.HS-1296-2

• Material: 6150CRV, A3 steel, plastic, surface sandblasted, black scale
  Suitable for: disassembly and assembly of generator pulleys for models such as Volkswagen, Audi, BMW, Ford, Skoda, Mercedes Benz, Opel, Volvo, Porsche, Renault, etc

Leakage Detection Joint for Cold Gas Pipeline(Europe and America)ES.HS-1297-2

• Leakage Detection Joint for Cold Gas Pipeline(Europe and America) copper materials

15PCS Camshaft Crankshaft Wrench SetES.JY-1309-2

• Ideal for DIY: Whether you're an amateur or a seasoned do-it-yourselfer, this tool is perfect for anyone looking to maintain their vehicle's brake system. It's compatible with various vehicle models, making it a must-have in any toolkit

Engine Brake Adjustment Tools for Cummins ISX Engine Jake Brake Feeler Gauge（4.1mm,4.6mm,7mm）ES.JY-1312-2

• excellent performance, also avoid any unwanted catastrophic failures or engine blows .
  (2)Engine brake adjustment tool 3.4 MM alternative to # 5298757 .
  (3)The 3.4mm area is precision ground to +/- .0005 inch .
  (4) Made of high standard steel anodized black finish,with great strength and PVC coated handle. Design with OEM data, directly replace .

  Using Instruction
  1.Loosen the locknut on the brake lever adjusting screw, and back out the adjusting screw one turn.
  2.Insert the feeler gauge( 3.4 mm shim, between the bottom of the engine brake piston and the top of the exhaust valve pin on the exhaust valve crosshead.
  3.Tighten the adjusting screw until drag on the feeler gauge is felt.
  (Proper drag means that there is no motion of the brake lever camshaft follower against the cam lobe.)
  4.Hold the engine brake lever adjusting screw and tighten the locknut.

Universal Pneumatic Fuel Diesel Injector Puller Extractor Removal Tool with BOSCH 110 Common Rail Diesel Injector Tester PullerES.HTL-1359-2

• Wide Application: This kit fit most diesel engine, compatible with Benz, compatible with Bosch 110 120, compatible with Cummin, compatible with Siemens, compatible with Denso, etc
  Easy To Remove Diesel Injector: Usually, it 's difficut to remove stubborn diesel fuel injector by manually operated, this kit is specifically designed to use pneumatic hammer to pull dieseal injector. Its unique feature is its air vibrating hammer action. This hammering action creates a rapid vibrating motion on the injector. This rapid hammering action helps to release the bond between the injector and the engine block, making removal of the diesel injector easier and more efficient
  With Pneumatic Hammer: The pneumatic hammer horsepower is 1000NM, connect 0.6-0.8 bar pressure, 20-30 impacts per second. which will help you quick pull out diesel injector, and also suitable for tight spaces
  Conversion Screw Specification : It include for Bosch 110; for Bosch120; for Denso; for Cummin; M8-C; M8-X; M10; M12; M14; M15; M17; M19; CRIN1; CRIN2; BY; CY; CAT320; XF. if you don't know whether fit your car, please measure your car injector screw size
  A Complete Set: This kit includes 20pcs conversion screw adapters, pneumatic hammer, puller hook, connect tube, valve with US standard, EU standard connector, 2pcs extension rod and screw. This tube length is 31.5 inches, one side connect pneumatic hammer, another side connect valve switch, the valve switch could control the turn on or off. This extension rod is 11.8" and 5.4", used for deeper located injectors. This puller hook is used to pull out injectors that are relatively deep in position

Engine Injector Removal Puller for VW Audi Diesel Injector ToolsES.HTL-1361-2

• Wide Vehicle Compatibility: Specifically designed for VW/Audi TDI engines (1.6L & 2.0L), perfect for Compatible with Audi A3 (2009/2013),Volkswagen Golf (2009),Seat Ibiza (2008),Toledo (2013),Altea, Leon, Altea XL, Altea Freetrack (all 2009)
  All-in-One Professional Kit: Includes all necessary tools for efficient injector removal, conveniently organized in a heavy-duty portable case for easy transportation and workshop use
  Professional-Grade Construction: Made from high-quality, multi-forged steel with superior hardness and corrosion resistance for maximum durability during tough injector removal jobs
  OEM Part Number & Save Costs: Direct replacement for T10402 and T10415 tools, providing the same professional results at a fraction of the OEM cost.Perfect for DIY mechanics or professional workshops handling VW TDI fuel injector issues.

   

Clutch Alignment Tool Kit (for BMW)ES.HTL-1385-2

• Function: SAC clutch mandrel kit for centering the clutch disc on the flywheel while installing the self adjusting clutch; also be used to align new and previously pre-tensioned SAC clutches
  Application: compatible with BMW
  Function: SAC clutch mandrel kit for centering the clutch disc on the flywheel while installing the self adjusting clutch; also be used to align new and previously pre-tensioned SAC clutches

Double-Clutch Transmission Tool for VAG VW AUDI 7 Speed DSG Clutch Installer Remover T10373 T10376 T10323 T10407ES.HTL-1396-2

• For AUDI VW T10134 1.4 1.6 Crankshaft Seal Flange Installing Tool
  Designed for DSG 7 speed dual clutch Drect Shift Gearboxes fitted to VAG VW audis Seat skodas vehicles
  Assembly lever for use on DSG gear boxes

Dual Clutch Transmission DSG Remover Installer Tool Kit Compatible with Ford DPS6 Dual Clutch Reinstall Reset ToolES.HTL-1398-2

• Removal Install Dual Clutch: Special designed to disassembly and install dry transmission. Disassemble the double clutch fixing snap ring, install and remove the three claws, turn the threaded bar 20 turns after it makes contact with the input shaft and pull out the double clutch
  Reinstall Reset Dual Clutch: this tool could resprings/re-trips the springs on the clutch so that you can Disassembly lock and installing an unlock
  FM number: 307675
  Applicable: compatible with ford dual clutch transmission DPS6. vehicle include: Fiesta 2011-2019; Focus 2012-2018; Transit Connect 2019; B-MAX since 2012

Dual Clutch Transmission DSG Gearbox Lock and Unlock Tool for Ford 1.0ES.HTL-1399-2

• Ford 1.0

15 Pieces Super Complete Auto Car Radiator Water Fuel Hose Clamp Pliers Tools Set Kit Removal Tool SetsES.HTL-1407-2

• A Complete Hose Clamp Pliers Set: This hose clamp tool set include 1pc flexible hose clamp pliers, 1pc angled flat band hose clamp pliers, 1pc swivel jaw spring wire clip pliers, 1pc flat band hose clamp pliers, 1pc swivel jaw band clip pliers, 1pc Clic-R collar pliers, 1pc hose removal pliers, 1pc fuel -headed screwdriver, 1pc hose removal hook, 1pc 1-3/4”, 1”, 1/2” and 3/8” hose pinch off pliers, 1pc electrical disconnect pliers and 1pc straight electrical disconnect pliers
  Must Have Tool for Hose Clamp: Spring clamps can be a headache during hose and accessory repairs, as limited space and access angles can turn a simple task into a hassle. Rusty, tight, baked-on hose clamps can make repairs even more problematic. But with this hose clamp tool set with multiple types and sizes, it will make your hose clamps and fittings and other disassembly work easier, is the any mechanic or automotive enthusiast 's essential hose clamp tool
  Wide Application: Our hose clamp pliers are designed to remove and replace hose clamp, used on those hard to reach factory clamps in tight spaces, works with hose clamps from 11/16 inch to 2-1/2 inches. Fit for removing radiator hose, engine coolant hose, water pump and radiator job, electrical connectors, fuel vacuum lines, fuel lines, etc. Compatible with GM Ford VW Audi BMW Toyota and Volvo vehicles and more

Brake Pipe Flaring Tool Professional Brake Line Double Flaring Tool Kit 45 Degree Set Other Vehicle ToolsES.HTL-1411-2

• Multi Purpose Flaring Tool: This is a multi-functional brake line flaring tool. Used to create 45-degree single, double and bubble brake flares on 304 stainless steel, steel and soft metal tubing in a short time. It produces flares of high quality and accuracy that do not lead to subsequent leaks in hydraulic or brake lines, making it a must-have brake flaring tool for the DIY or mechanic
  Wide Application: This flaring tool can be used with 3/16", 1/4", 5/16", 3/8" and 4.75mm diameter lines, Suitable for automotive brake lines, transmission cooler lines and fuel lines and more
  Professional Brake Flaring Tool: Made of high quality steel and heat-treated and oxidized, it is extremely hard, durable and not easy to be damaged; at the same time, it has been professionally designed and rigorously tested to be highly accurate and stable, and it can produce many types of perfect flares in a short period of time, it is professional brake line and tubing flaring tool
  Easy to Make Perfect Flares: First, select the flat face die, place the tool in a secure vise, tighten the clamps so they do not move; Second, loosen the clamps, select the desired parting size, insert the die into the rectangular recess in the base of the tool, place the tube between the two halves of the die; Then, turn the clamps back to their original position, OP.0 is aligned with the port of the tube, push the OP.0 to press it into the port of the tube; Finally, select the desired, select the desired size of reaming cone OP.1, align the tube port, turn the handle and press it into the tube port, then, select the desired size OP.2, repeat the operation, and you can easily complete flare

Brake Pipe Flaring Tool Professional Brake Line Double Flaring Tool Kit 45 and 37 Degree Set Other Vehicle ToolsES.HTL-1412-2

• 7 and 45 Degree Flaring Tool: This is a multi-functional brake line flaring tool. Used to create 37 and 45 degree single, double and bubble brake flares on 304 stainless steel, steel and soft metal tubing in a short time. It produces flares of high quality and accuracy that do not lead to subsequent leaks in hydraulic or brake lines, making it a must-have brake flaring tool for the DIY or mechanic
  Wide Application: This flaring tool can be used with 3/16", 1/4", 5/16", 3/8" and 4.75mm diameter lines, Suitable for automotive brake lines, transmission cooler lines and fuel lines and more
  Professional Brake Flaring Tool: Made of high quality steel and heat-treated and oxidized, it is extremely hard, durable and not easy to be damaged; at the same time, it has been professionally designed and rigorously tested to be highly accurate and stable, and it can produce many types of perfect flares in a short period of time, it is professional brake line and tubing flaring tool
  Easy to Make Perfect Flares: First, select the flat face die, place the tool in a secure vise, tighten the clamps so they do not move; Second, loosen the clamps, select the desired parting size, insert the die into the rectangular recess in the base of the tool, place the tube between the two halves of the die; Then, turn the clamps back to their original position, OP.0 is aligned with the port of the tube, push the OP.0 to press it into the port of the tube; Finally, select the desired, select the desired size of reaming cone OP.1, align the tube port, turn the handle and press it into the tube port, then, select the desired size OP.2, repeat the operation, and you can easily complete flare

Camshaft Pulley Removal Install Tool for Subaru Forester 3 TeethES.HTL-1413-2

• 【Exhaust Cam Lock Tool for STD】Direct replacement for OEM part number 499207400 and 499207400-A. Fits for Subaru 2005-2006 Saab 9-2X; Fits for 2002-2007 Impreza WRX STI; Fits for 2006+ Impreza WRX; Fits for 2004+ Impreza WRX STI; Fits for 2004-2006 Baja Turbo.
  【Intake Cam Sprocket Wrench Tool】Comparable to the factory tool #499977500 both in quality and functions. Fits for 2004+ Subaru Impreza WRX STI Includes for JDM Ver.9 STI; Fits for 2006-2014 Subaru Impreza WRX; Fits for 2004-2011 Subaru Forester XT; Fits for 2005-2010 Subaru Legacy GT; Fits for 05-10 Subaru Outback XT.

Camshaft Pulley Removal Install Tool for Subaru Forester 12 TeethES.HTL-1414-2

• 【Exhaust Cam Lock Tool for STD】Direct replacement for OEM part number 499207400 and 499207400-A. Fits for Subaru 2005-2006 Saab 9-2X; Fits for 2002-2007 Impreza WRX STI; Fits for 2006+ Impreza WRX; Fits for 2004+ Impreza WRX STI; Fits for 2004-2006 Baja Turbo.
  【Intake Cam Sprocket Wrench Tool】Comparable to the factory tool #499977500 both in quality and functions. Fits for 2004+ Subaru Impreza WRX STI Includes for JDM Ver.9 STI; Fits for 2006-2014 Subaru Impreza WRX; Fits for 2004-2011 Subaru Forester XT; Fits for 2005-2010 Subaru Legacy GT; Fits for 05-10 Subaru Outback XT.

Subaru 2.5 dual camshaft retaining toolES.HTL-1418-2

• Subaru Camshaft Alignment Tool
  Subaru 2.5L DOHC non-turbo engines, Impreza, Legacy, SVX. STi 2.0L EJ20 (2002-2005), STi 2.5L EJ25 (2005-2014)
  OEM Code: 499207300

Nissan/Honda CVT hydraulic cylinder pullerES.HTL-1419-2

• Universal CVT Hydraulic Cylinder Puller for Audi Nissan BMW Mini 01J 0Aw VT1 VT2 VT3 JF015

50mm Crankshaft Crank Pulley Wrench Holder Tool Removal Holding Spanner kit Compatible with Honda and Acura EnginesES.HTL-1421-2

• Professional grade 50mm socket (with offset design) for removing/installing many Acura and Honda engine crank bolts
  This socket is used to maintain the harmonic damper pulley position while removing/installing the pulley bolt.
  Use with square socket driver.> 1/2" square drive use with breaker bar
  Designed with hardened chrome molybdenum steel construction
  Backed by a lifetime replacement guarantee

Tool for Honda Gearbox Gear PullerES.HTL-1423-2

• EFFICIENT TIMING GEAR REMOVAL: The Performance Tool W87010 Timing Gear Puller helps you remove timing gears and other gears with tapped holes easily and efficiently.
  CORROSION-RESISTANT: The drop-forged yoke is plated to resist corrosion and maintain durability even with regular use.
  HEAT-TREATED CENTER SCREW: The heat-treated center screw ensures that the puller can handle tough and heavy-duty jobs with ease.
  TWO BOLTS INCLUDED: The kit includes two 5/16-Inch x 4-Inch bolts, so you don't need to worry about purchasing additional hardware.
  ADJUSTABLE PULLER SPREAD: The puller has an adjustable spread of 1-1/2 to 4-1/4-Inches, making it suitable for a range of application

Ninth-generation Accord steering gear disassembly, right rack bushing pressure block screw wrench and disassembly tool socketES.HTL-1428-2

• Specifically designed for the right-side rack bushing mounting screw of the ninth-generation Accord (2013-2017) steering gear, this product is 100% compatible with the original vehicle's special internal hexagon Torx specifications (such as T50/E type, etc., with specific dimensions to be confirmed).
  The internal threads of the socket engage fully with the screw head at all angles, ensuring zero play and zero stripping, thereby eliminating screw head damage at the source.
  Forged from heavy-duty chromium-vanadium alloy steel (Cr-V), undergoes heat treatment and carburizing processes, achieving a hardness of HRC 50-55.
  Torsional strength increased by 300%, capable of withstanding extremely high torque from rusted screws without chipping, deformation, or breakage.
  The extended socket body (recommended to specify the exact length, e.g., 80mm) reaches deep-set screws without the need for repeated angle adjustments.
  Internal precision knurled anti-slip grooves + strong magnetic adhesion at the bottom ensure the socket never detaches during screw installation/removal, significantly boosting efficiency.

Honda crankshaft pulley tensioning support wrench (extended)ES.HTL-1429-2

• Crankshaft Pulley Retainer Removal Support Wrench for Honda Civic Odyssey

Toyota Lexus crankshaft pulley support wrenchES.HTL-1431-2

• Applicable: Compatible with Lexus from 1990: 3.0 L6, 3.0 V6, 3.3 V6, 4.0 V8, 4.3 V8, 4.7 V8; Compatible with Toyota from 1996 : 3.0 V6, 3.3 V6, 4.0 V6, 4.7 V8. fit 4 cyl engine : 1983-1995 22RE, 1995-2004 2RZ,1995-2004 3RZ
  Function: Prevent the harmonic damper pulley from rotating in the process of removing and setting the final torque specification on the pulley bolt, allowing users to easily remove and install the crank bolt on engines
  Tips: need used with an inch drive impact wrench and a 22 mm impact sleeve to unscrew the crank bolt, or need a cheater bar to connect to this tool
  Note: This crankshaft pulley not compatible Toyota Solara 2.2L, Not compatible with Toyota's 3.4 l motor, Not compatible with tacoma v6 3.4, please carefully check

Toyota Crown, Reiz, and Lexus differential bushing installation toolES.HTL-1432-2

• Install Differential Rubber Bushing Tail Teeth: This tool is used to install the differential rubber bushing tail teeth of the differential
  Easy To Use: No need to dismantle the rear axle, can be installed differential rubber bushing tail tooth directly
  Application Vehicle: Compatible with Toyota Reiz, Crown, Lexus
  Package Includes: Differential rubber bushing, one 89mm screw and One 68mm screw. Note: 89mm screw Compatible With Toyota Reiz Crown Lexus, 68mm screw Compatible With Reiz
  Tips for Reiz Installation: Single hole addition on right side, Clean dust from mounting location, and grease. Put the tool new glue in the hole assembly well, at the mouth of the cave, Assembly Completion Tool New Glue, Screw in tail tooth differential, Press the new adhesive into, left side double hole installation, first half of the lower hole, and then the upper hole to flatten the

Engine Cam Gear Lock Timing Belt Installation Tool Compatible with Mitsubishi Eclipse DSM 4G63 EVOES.HTL-1439-2

• Compatible with Mitsubishi 4G63 Cam Gear Lock/Timing Belt Installation Tool.
  EASY TO USE:This precision tool makes the job of replacing or setting up your new Timing Belt as easy as 1,2,3.

Toyota Lexus U-shaped oil filter wrench, oil filter, and special tools for Toyota Reiz and HighlanderES.HTL-1444-2

• FIT VEHICLES:Oil Filter Wrench Tool Compatible with Lexus ES300h, ES350, GS300, GS350, GS450h, RX350, RX350h, etc. Toyota C-amry, Highlander, Land Cruiser, Rav4, 4Runner, Tundra, etc
  PREMIUM QUALITY:Made of high quality steel material, wear-resistant, not easy to break, corrosion resistance, durable
  WIDE APPLICATION:Oil Filter Wrench Removal Tool Drive: 3/8 . 0.25 " open, 3.16 " length
  FUNCTION:The oil filter tool is used to remove the automotive oil filter housing. It is installed directly without getting stuck in the filter housing
  Package includes : one Oil Filter Wrench Tool

Hyundai and Kia 1.0, 1.2, 1.6, and 2.0 2.4 Flywheel Lock ToolES.HTL-1445-2

• OE Number: This engine flywheel locking kit is molded to match the original car data, and the OE reference number is 09231 2B100. This ensures that it's a fit and works well with your vehicle.
  Wide Fitment: Engine Flywheel Holding is a versatile tool suitable for various car . Additional details are available in the parameters section to determine if this product is compatible with your vehicle.
  Efficient Features: This engine flywheel locking kit is the tool to ensure that the crankshaft remains locked while removing and torquing crankshaft pulleys, clutch bolts, and flywheel bolts. It'll make your job easier and more efficient.
  Versatile Function: This tool is ideal for engine rebuilds and timing chain use. Made of high-strength steel, it is robust and , making it less prone to breakage.
  Easy Installation: The engine flywheel locking kit is very easy to install. You only need to bolt it in place of your starter, and it will lock securely into the flywheel teeth. It's an effortless way to make your vehicle maintenance run more smoothly.

Hyundai/Kia DTC Automatic Transmission Clutch ToolES.HTL-1446-2

• Specialized Tool: This DTC Dual Clutch Transmission Actuator Tool is designed specifically for Hyundai Kia Elantra Tucson
  Must-Have Repair Tool: A must-have accessory for automotive technicians and DIY enthusiasts.
  Efficient Operation: Simplifies the actuator removal, installation and adjustment process, saving valuable time and effort.
  Material：Durable Construction: Made with premium materials to ensure reliable performance and longevity during automotive repair tasks.

6-piece exhaust temperature sensor socket removal tool set for cars, trucks, and light trucksES.HTL-1455-2

• Sockets are designed to install and remove EGT sensors without damaging connection wire, housing and sensor threads
  Opening in hex working end for clearance
  The offset and straight options make selecting the correct socket easy
  Offset sizes: 13mm, 14mm & 17mm

Diesel filter sensor removal socketES.HTL-1456-2

• Application: Ford Transit Custom Mk8 2.0 TDCi (from 2016).
  Size: 32mm x 1/2"D x Single Hex (6pt) profile.
  Cut-outs in the socket clear the fuel drain valve.
  Manufactured from chrome vanadium.

New energy refrigerant filler connectorES.HTL-1457-2

• 【WIDE APPLICATION】The R12 AC flow control valve adapter fits for R12 R22 air conditioner manifold with 1/4" Male to 1/4" Female. The R410 Refrigerant Charging Valve manifold with 1/4" Male to 5/16" Female.
  【PREMIUM QUALITY】The R12 R22 R410 control valve adapter is made of high quality brass material, with high strength and durable to use.
  【EASY TO INSTALL】The R12 refrigeration charging safety adaptor with 1/4" SAE and 1/4" Female Thread. The R410 refrigeration charging safety adaptor with 1/4" SAE and 5/16" Female Thread. The R12 R410a refrigerant charging valve is easy to install, just install on the end of a charging hose and minimize refrigerant loss during servicing.

Tesla M3/MY radiator connectorES.HTL-1460-2

• Radiator Pressure Tester Adapter Water Tank Leak Detection Connector Adapter for Telsa Model 3 Y

Tesla MS/MX radiator connectorES.HTL-1461-2

• Cooling System Pressure Radiator Pressure Tester Adapter Water Tank Leak Detection Connector Adapter for Telsa Model X Model S

Electric vehicle motor shaft disassembly and assembly tool in a plastic boxES.HTL-1463-2

• Function: This tool is used to dismantle worn out motor shafts of new energy vehicles or to replace them with new shafts to press them into the motor
  Easy to Use: This tool is used to fix the magnetic steel sheet of the motor shaft from both ends, after locking the screws, it can be used with the press to press out the shaft
  Applicable Vehicles: Compatible with Tesla, Jeep, Honda, Hyundai, Chevrolet, GM and other new energy vehicles
  Tip: When your new energy vehicle travels more than 20w kilometres, there may be strange noise, skidding or motor idling, which means that the motor shaft has been seriously worn out, and needs timely repair
  "Package Includes: 2* motor mounting tool, 4* bolts. High Quality Material: The tools are made of high quality material, durable and able to work for a long time with high intensity"

Ford Volvo dry transmission dual clutch disassembler (DPS6)ES.HTL-1491-2

• Fit: compatible with VOLVO, compatible with FORD, transmission DPS6,replace FM number: 307675. While is not a original, it is a direct replacement and completely fit, and our offer quality guarantee, which will help you save much money
  As Accurate As OEM: All the tools have been engine tested and strict quality inspection, to ensure compatibility with the engine, even some our designs are better and last longer than those of the original manufacturers
  Professional Tool: Special designed to disassembly dry transmission and align the twin-clutchto change the oil seal
  , our tool designed and manufactured by professional engineers, which let you choose no worry
  Material: The twin clutch dry transmission installer &remover tools' material is heavy duty steel, anti-corrosion and hardness, so have a long service life
  Instruction: Install the special tool and compress the input shaft. Turn the threaded bar 20 turns after it makes contact with the input shaft

Ford Volvo dry transmission dual clutch plate reset tool (DPS6)ES.HTL-1492-2

• Function: Specially designed to release and reset the dual clutch before installing back to the transmission.
  Application: compatible with Ford Volvo DPS6 dry type dual clutch.
  Vehicle include:
  for Fiesta 2011-2019;
  for Focus 2012-2018;
  for Transit Connect 2019;
  for B-MAX since 2012 ect.

Ford Volvo fuel injector removal toolES.HTL-1493-2

• 【Compatible with Ford and Volvo】 The fuel injector remover tool Compatible with Ford and Volvo engines. Compatible with Ford replacement for Volvo 1.0L, 2.0L Duratec engine, compatible with Ford 1.0L, 1.5L, 1.6L, 2.0L, 2.3L, 2.7L, 3.5L EcoBoost engine, compatible with 2.0L, 3.5L GTDI.
  【Completely Replacement】 Our fuel injector remover puller kit can replace to OEM 310-206, 9997410 Directly.
  【Function】The fuel injector remover tool specially designed for correct removing the injection nozzles of petrol and diesel engine with slide hammer. You can dismantle the injectors efficiently, labor-savingly and safely.
  【Premium Material】 The fuel injector remover tool is made of high carbon steel and copper with galvanized surface to prevent rusting, hardness and durability.
  【Excellent Carrying Case】 Our fuel injector remover puller kit comes with carrying case. The carrying case allows for stable and secure storage of multiple adapters. Dedicated grooves inside the carrying case hold the accessories in place and keep them stable during transportation without being disrupted or worn out by bumps and bruises.

Ford diesel high-pressure fuel pump disassembly and assembly kitES.HTL-1494-2

• Timing Tool Injection Pump Chain Sprocket Cover Remover Installer Compatible with Ford 2.0 2.2 2.4 3.2 TDDi TDCi Diesel Engine
  Function: Specially designed to remove and install high press pump sprocket cover, keep engine shaft in a specific position when change the timing belt or during other engine repair, and to replace the injection pump
  Applicable Engine: compatible with Ford 2.0 2.2 2.4 3.2 TDDi TDCi diesel engine, engine code: 2.0l: ABFA, D3FA, D5BA, D6BA, F3FA, FIFA, FMBA, HJBA,HJBB, HJBC, HJBE, N7BA, N7BB. 2.2l: QJBA(BG), QJBB, QJBC, QJBD. 2.2l: 4HM, 4HU, 4HV, P8FA, P22DTE, QVFA, QWFA. 2.4l: 244DT, D0FA, D2FA, D2FB, D4FA, F4FA, FXFA,H9FA, H9FB, replacement for HEFA, HFFA, JXFA, PHFA, ZSD 424. 3.2l: SAFA
  Applicable Vehicle: compatible with Ford: Puma, Mondeo (2000-2007), Transit (2000-2011);compatible with Land Rover: Defender (2007-2011);compatible with Jaguar: X-Type (2001-2010);compatible with Fiat: Ducato (2006-2011); compatible with Citroen: Jumper III, Relay (2006-2011); compatible with Peugeot: Boxer 3 (2006-2011); compatible with LDv: Convoy (2002-2006)
  OEM Equivalent Part Number: 303-682,303-679A,303-1151,303-249,303-675 and 303-698

Dry Type Transmission Oil Seal Disassembly and Installation Kit (DPS6)ES.HTL-1495-2

• Function:Use this tool to remove the input seal compatible with Ford Focus Festiva DCT DPS6 6DCT250 Dual Clutch Transmission
  Application: Compatible with Ford Focus (from 2012), Fiesta (from 2008), B-Max (from 2012), EcoSport (from 2013)
  OEM Equivalent Part Number: 307-671, 307-672, 307-673, 307-674
  Material: Made of high quality steel, high hardness, not easy to break, The exterior is coated with antioxidant layer or alloy plated, extended service life

Volvo Truck Cranking Gear Tool Flywheel Holder 99969ES.HTL-1496-2

• Allows the engine crank to be manually adjusted

• Allows pinpoint accuracy calibration

• Ideal for adjustments to the engine

• Adjusting screw in the clutch housing
  Application range:
  Alternatively for 6 or 12 liter VOLVO engines
  e.g. engine D9A, D12, D16C.
  Genuine Stock : VOLVO 9996956

Volvo Fuel Pump Removal WrenchES.HTL-1497-2

• 【Fitment】: Compatible with Volvo S60 2001-2009, S80 1999-2006 , V70 2001-2007, XC70 2003-2007 and XC90 2003-2014.
  【High Quality Material】: Made of high standard Aluminum with red finish, great strength and durability, anti-rust and anti-corrosion, can be used for a long time.
  【Ingenious Design】: Tooth shape design perfectly matches the plastic locking ring to prevent damage to the locking ring during installation or removal. It can help you to lock the fixing nut in place or remove it quickly and easily.
  【Multipurpose】: Designed to remove the left and right fuel pump fixing nuts (also called lock rings) of all latest model cars without removing the fuel tank.
  【Package Included】: 1 x Fuel Pump Socket. ----- Compared with the traditional method, it is easier to remove and install the fixing nut (locking ring).

Ford Volvo DCT Transmission Clutch Oil Seal Installation ToolES.HTL-1498-2

• DCT Wet Clutch MPS6 6DCT450 Transmission Oil Seal Cover Install Set Compatible with Ford Volvo 6 Speed Dual Clutch Transmission Replace 308-764 308-783 9997383 9997388
  Function: Specially designed to install the clutch oil seal cover on MPS6 transmission without damage the centre seal
  Widely Compatible: Compatible with Ford Focus (from 2004), Compatible with Kuga (from 2008), C-Max (from 2006), Galaxy (from 2006), S-Max (from 2006), Compatible with Volvo C30 (from 2006), C70 (from 2006), S40 (from 2004), S60 (from 2011 onwards), S80 (from 2007 onwards), V40 (from 2008 onwards), V50 (from 2008 onwards), V60 (from 2008 onwards), V70 (from 2008 onwards), XC60V60 (from 2008 onwards)
  OEM Equivalent Part Number: 308-764, 308-783, 9997383, 9997388
  Applicable: use on Getrag MPS6 DCT 450 transmission with dual wet clutch system

Ford DSG Clutch Release Tool 1/2"ES.HTL-1499-2

• 1/2" DSG Gearbox Clutch Motor Electromechanical Unit Unlocking Tool Fits for Ford Focus DPS6/6DCT250
  Compatoable with
  Transmission clutch tool fits for Ford Ecosport/Fiesta/Focus/Focus PS/Transit/Tourneo Connect /B-MAX 6 speed dry dual clutch DPS6 transmission
  Easy to use
  Insert the clutch release tool and turn counterclockwise to release the lock on the clutch until the clutch is fully open
  High-Quality Material
  Gearbox clutch motor electromechanical unit unlocking tool is made of high-quality high-hardness carbon steel material, which has
  stable performance, is not easy to rust, and has higher efficiency

Dual Clutch Transmission Clutch Motor Electromechanical Unit Unlock Tool Actuator Reset Tool Compatible with Ford DSG 6 Speed DPS6 6DCT250 Clutch 6mm 14 Spline Socket with 1/4" DriveES.HTL-1500-2

• Function: use to unlock dry dual clutch transmission clutch motor electromechanical unit, insert the reset tool into the lever actuator hole, turn the tool anti-clockwise to set new clutch
  Applicable: compatible with Ford DSG 6 speed dual clutch DPS6 transmission
  Applicable Vehicle Include: compatible with Ford Fiesta: 2011-2019; compatible with Focus: 2012-2018; compatible with Ford Transit Connect: 2019; compatible with Ford B-MAX: since 2012 ect
  Specifecation: 6mm size, 14 teeth, with 1/4'' drive
  Material: High quality steel